Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
An explosion could occur if grill lid is down. 2. Check that all burner control knobs and the natural gas supply are turned to the "OFF" position. 3. Turn on natural gas supply. 4. DO NOT stand with head, body, or arms over the grill when lighting. LIGHTING THE MAIN BURNERS: 1. Open lid before lighting burner. 2. Make sure all control knobs are in the "OFF" position. 3. Select the burner to be lit. Push and turn the control knob of that burner to the "HIGH" position. 4. Press the electronic igniter and hold for 3–5 seconds to light burner. 5. If ignition does NOT occur in 5 seconds, turn control knob to "OFF", wait 5 minutes to allow gas to dissipate and repeat lighting procedure. 6. Repeat Steps 3–5 for lighting each burner. Always use the electronic igniter for lighting each burner. If burner does not ignite using push-button igniter, wait 5 minutes, see ” Match Lighting the Main Burners” section. 7. To turn off, turn each control knob clockwise until it locks in the "OFF" position. This does not turn off the gas flow from the natural gas supply. Note: If burner does not light or flame is too low, you may have spider or other insect blockage in burner. See "Burner Assembly/Maintenance" under Proper Care and Maintenance. MATCH LIGHTING THE MAIN BURNERS: 1. Open lid before lighting. 2. Turn the burner control knobs to “OFF”. 3. Strike the match and place approximately 1/2" (1 to 2 cm) above lighting hole located on right and left hand side of the grill body. 4. Turn right or left burner control knob to the “HIGH” position. The burner should light within 5 seconds. 5. If the burner does not light, turn the control knob to “OFF” and wait 5 minutes for gas to evacuate the grill. Repeat Steps 1 through 5 until the burner ignites. 6. Once lit, light adjacent burners in sequence by pressing in and rotating the control knob to the “HIGH” position. 7. If the burner does not light within the first few attempts of match lighting, there is a problem with the gas supply. Turn off the gas at the burner and cylinder. DO NOT attempt to operate the grill until the problem is found and corrected. See “Trouble Shooting” section of this manual. Lighting Hole Match LIGHTING THE ROTISSERIE BURNER: 1. Open grill hood before lighting rotisserie burner. 2. Make sure control knob is in the "OFF" position. 3. Push and turn the control knob to the "HIGH" position. Continue to push in control knob while pressing electronic igniter for 3–5 seconds. 4. Once burner is lit, continue to push and hold control knob for 30 seconds. 5. If ignition does NOT occur in 5 seconds, turn control knob to "OFF”, wait 5 minutes to allow gas to dissipate and repeat lighting procedure. 6. To turn off, turn control knob clockwise until it locks in the "OFF" position. IMPORTANT: DO NOT use back rotisserie burner when main burners are in use. Note: If burner does not light or flame is too low, you may have spider or other insect blockage in burner. See "Burner Assembly/Maintenance" under Proper Care and Maintenance. MATCH LIGHTING THE ROTISSERIE BURNER: 1. Open grill hood before lighting rotisserie burner. 2. Make sure control knob is in the "OFF" position. 3. Strike and carefully place a match approximately 1/2" (1 to 2 cm) from the lower edge of burner. 4. Push and turn the control knob to the "HIGH" position. Continue to push in control knob for 3-5 seconds while holding match under burner. The burner should light within 5 seconds. 5. Once burner is lit, continue to push and hold control knob for 30 seconds. 6. If the burner does not light, turn the control knob to "OFF" and wait 5 minutes for gas to dissipate and repeat lighting procedure. 7. If the burner does not light within the first few attempts of match lighting, there is a problem with the gas supply. Turn off the gas at the burner and natural gas supply. DO NOT attempt to operate the grill until the problem is found and corrected. See "Trouble Shooting" section of this manual. LIGHTING THE SIDE BURNER: 1. Open lid before lighting side burner. 2. Make sure control knob is in the "OFF" position. 3. Push and turn side burner control knob to the "HIGH" position. 4. Press the electronic igniter on the side burner and hold for 3–5 seconds to light burner. 5. If ignition does NOT occur in 5 seconds, turn control knob to "OFF", wait 5 minutes to allow gas to dissipate and repeat lighting procedure. 6. To turn off, turn each knob clockwise until it locks in the "OFF" position. Note: If burner does not light or flame is too low, you may have spider or other insect blockage in burner. See "Burner Assembly/Maintenance" under Proper Care and Maintenance. MATCH LIGHTING THE SIDE BURNER: 1. Open the lid to the side burner before lighting. 2. Make sure control knob is in the "OFF" position. 3. Strike and carefully place a match approximately 1/2" (1 to 2 cm) from the burner. 4. Turn the side burner control knob to the "HIGH" position. The burner should light within 5 seconds. 5. If the burner does not light, tur...