Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Indicates a potentially hazardous situation, Specifi cations Fuels Firing range Motor Igniter. Housing Fuel unit Oil nozzle Shipping wt. U.S. #1 or #2 Fuel Oil only (ASTM D396) Canada #1 Stove Oil or #2 Furnace Oil only CF500: 1.75 to 5.50 GPH CF800: 3.00 to 8.00 GPH 1/3 HP 3450 RPM 120/60 hz standard 4.8 amps @ 120 VAC 120V/14,000V Cast aluminum 100 - 200 PSIG 45° - 70° solid 55 lbs. which, if not avoided, may result in personal injury or property damage. NOTICE Intended to bring special attention to information, but not related to personal injury or property damage. Note: Within the boundaries of the hazard warning, there will be information presented describing consequences if the warning is not heeded and instructions on how to avoid the hazard. Agency approvals UL listed to comply with ANSI/UL296 and certifi ed to CSA B140.0. Accepted by N.Y.C. M.E.A. Other approvals may be available and must be specified at time of order. Form 6104BCF5 R09, Printed in the USA 01/08 Owner’s Responsibility: Follow These Instructions Exactly Failure to follow these instructions, misuse, or incorrect adjustment ofthe burner could lead to equipmentmalfunction and result in asphyxiation, explosion or fire. Contact a professional, qualified service agency for the installation, adjustment and service of your oil burning system. Thereafter, have your equipment adjusted and inspected at least annually to ensure reliable operation. This work requires technical training, trade experience, licensing or certification in some states and the proper use of special combustion test instruments. Please carefully read and comply with the following instructions: • Never store or use gasoline or other fl ammable liquids or vapors near this burner or appliance. • Never attempt to burn garbage or refuse in this appliance. • Never attempt to light the burner by throwing burning material into the appliance. • Never attempt to burn any fuel not specified and approved for use in this burner. • Never restrict the air inlet openings to the burner or the combustion air ventilation openings in the room. Professional Installer/Service Agency Responsibility: Follow These Instructions Exactly Failure to follow these instructions could lead to equipment malfunc tion and result in asphyxiation, explosion or fire. • Please read all instructions before proceeding. Follow all instructions completely. • This equipment must be installed, adjusted and started by a qualified service agency that is experienced with all applicable codes and ordinances and responsible for the installation and commission of the equipment. • The installation must comply with all local codes and ordinances having jurisdiction and the latest editions of the NFPA 31 and CSA-B139 & B140 in Canada. NOTICE 50 Hz motors — The burner ratings, air settings and nozzle ratings are based on standard 60 hz motors (at 3450 rpm). Derate all ratings 20% when using 50 hz motors. Consult factory for specific application data. NOTICE High altitude installations — Accepted industry practice requires no derate of burner capacity up to 2,000 feet above sea level. For altitudes higher than 2,000 feet, derate burner capacity 2% for each 1000 feet above sea level. Pre-installation checklist • Combustion air supply Adequate Combustion and Ventilation Air Supply Required Failure to provide adequate air supply could seriously affect the burner performance and result in damage to the equipment, asphyxiation, explosion or fi re hazards. • The burner cannot properly burn the fuel if it is not supplied with a reliable combustion air source. • Follow the guidelines in the latest editions of the NFPA 31 and CSA-B139 regarding providing adequate air for combustion and ventilation. • The burner requires combustion air and ventilation air for reliable operation. Assure that the building and/or combustion air openings comply with National Fire Protection Standard for Oil-Burning Equipment, NFPA 31. For appliance/burner units in confined spaces, the room must have an air opening near the top of the room plus one near the floor, each with a free area at least one square inch per 1,000 Btu/hr input of all fuel burning equipment in the room. For other conditions, refer to NFPA 31 (CSA B1139-M91 in Canada). • If there is a risk of the space being under negative pressure or of exhaust fans or other devices depleting available air for combustion and ventilation, the appliance/burner should be installed in an isolated room provided with outside combustion air. • Clearances • With the burner installed in the appliance, there must be adequate space in front of and on the sides of the burner to allow access and operation. Verify that the clearance dimensions comply with all local codes and with the appliance manufacturer’s recommendations. Form 6104BCF5 R09, Printed in the USA 01/08 • Fuel supply Oil Supply Pressure Control Required Damage to the pump, filter or other component seals could cause possible oil leakage and potential f...
Dieses Handbuch ist für folgende Modelle:Konvektionsöfen - CF800 (1.09 mb)