Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
CAUTION: OPERATION OF A PROPANE GAS GRILL AND SIDE BURNER WITHOUT THE PRESSURE REGULATOR AND HOSE ASSEMBLY WILL CAUSE GAS LEAKS WHICH COULD LEAD TO FIRE OR EXPLOSION, RESULTING IN PROPERTY DAMAGE OR PERSONAL INJURY. The pressure regulator’s fitting must remain clean and free of nicks and scratches. A dirty, nicked or scratched fitting can cause a gas leak, resulting in an explosion or fire. Use only genuine Broilmaster® replacement parts unless otherwise specified by the manufacturer. Pressure Regulator and Hose Assembly If your grill is equipped with a factory installed gas "tee" behind the grill’s control panel, please skip to the next section. Turn OFF the gas valve at the propane cylinder. Disconnect the regulator and hose assembly from the cylinder. Disconnect hose from the gas valve located under the grill’s control panel. FIGURE 9. Attach one end of the 10" S/S flex line (22) to the end of the grill’s gas valve. Attach the other end of the S/S flex line to the brass "tee" (20). FIGURE 10. NOTE: GRILLS MANUFACTURED PRIOR TO 1999 MAY REQUIRE THE ALTERNATE "TEE" CONNECTOR. Installing “Tee” Connector (Continued) Attach the regulator and hose assembly to the brass tee" (20). Reconnect the assembly to the cylinder. Use two adjustable wrenches to hold and tighten the joint between the hose and "tee". FIGURE 12. PROPANE GAS CONNECTION Connecting to Propane Gas Attach one end of the 34" S/S flex line (23) to the end of the side burner valve (6). Attach the remaining end of the hose to the "tee" (20) and use two wrenches to tighten the S/S flex line connections. One wrench should be used to turn the S/S flex line connector while the "tee" or valve is held with the second wrench. FIGURE 11. FIGURE 20 12 FIGURE 10 Grill Gas Valve "Tee" (20) 10" S/S flex line (22) FIGURE 9 Grill Gas Valve Hose Assembly FIGURE 11 "Tee" (20) 34" S/S flex line (23) 6 For old Broilmaster grill, this alternate tee fitting kit must be ordered. NATURAL GAS CONNECTION NATURAL GAS CONNECTION Side Burner Location Your grill and side burner have been designed for outdoor use ONLY. This side burner mounts on the right side of a Broilmaster® gas grill and cannot be used with another grill or for any other purpose. You should never install or operate your grill and side burner in any building, garage, or other enclosed area. For your safety, the grill and side burner should not be installed or operated under any combustible materials, such as carports, covered porches, awnings, or overhangs. Never install or use your grill and side burner in or on any recreational vehicle or boat. CAUTION: THE INSTALLATION AND OPERATION OF THIS GRILL AND SIDE BURNER AT CLEARANCES LESS THAN SPECIFIED BELOW MAY CAUSE A FIRE, PROPERTY DAMAGE, OR PERSONAL INJURY. A minimum clearance of sixteen (16") inches is required from all sides of the side burner to any combustible material. Refer to the grill’s Owner’s Manual for specific grill clearances. Examples of combustible materials are patio furniture, fences, or the wall of your home. The area surrounding the grill and side burner should be clear to ensure proper ventilation. Do not obstruct the flow of combustion and ventilation air in any way. The ventilation openings on the propane cylinder enclosure must also remain free and clear of debris. Portable grills with side burners should be level and positioned away from direct wind prior to each use. WARNING: DO NOT INSTALL OR OPERATE THIS GRILL AND SIDE BURNER WHERE GASOLINE OR OTHER FLAMMABLE MATERIALS ARE USED OR STORED. FAILURE TO COMPLY WITH THIS WARNING COULD RESULT IN EXPLOSION OR FIRE CAUSING PROPERTY DAMAGE OR PERSONAL INJURY. Gas Type Your Broilmaster® side burner is factory equipped for LP gas and must be converted for use with Natural gas grills. Never use liquid propane gas with a grill designed for natural gas, or natural gas with a grill designed for liquid propane gas. The type gas required for your grill can be determined from its product identification label. Questions regarding different types of gases should be directed to your gas company. CAUTION: NEVER USE LIQUID PROPANE GAS IN A GRILL DESIGNED FOR NATURAL GAS, OR NATURAL GAS IN A GRILL DESIGNED FOR LIQUID PROPANE GAS. QUESTIONS REGARDING DIFFERENT TYPES OF GASES SHOULD BE DIRECTED TO YOUR LOCAL GAS COMPANY. BURNER TOP 89 BRASS DENOTES (LP) ORIFICE BRASS ORIFICE SHUTTER SCREW SHUTTER RING 173 DENOTES SIDE (NAT) BRASS BURNER ORIFICE 1. Remove shutter screw. Important: Do not discard this screw; it will be reinstalled. 2. Remove shutter ring. The shutter ring is not used for Natural gas, but retain for future use if LP conversion is desired. 3. Use a 7 mm nut driver or socket wrench to remove the LP orifice and replace it with the Natural gas orifice supplied. 4. Replace the shutter screw. 5. Turn set screw in center of valve stem 1/2 turn counterclockwise. 6. Apply soapy solution to test for leaks around the set screw. If a leak is found, turn screw clockwise until bubbles cease. IMPORTANT: PLAC...