Stimmen - 4, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: KitchenAid Dateigröße: 985.46 kb Dateiname: Unterrichtssprache:

psig (3.5 kPa). Gas Connection Requirements Natural Gas Built-in grill models are equipped for use with Natural gas. They are design-certified by CSA International for LP (propane) gases with appropriate conversion. Built-in models are set for Natural gas use and have a pressure regulator with ." female pipe threads. The supply line shall be equipped with an approved shutoff valve. This valve should be located in the same area as the grill and should be in a location that allows ease of opening and closing. Do not block access to the shutoff valve. The valve is for turning To convert to LP gas, the LP Gas Conversion Kit Part Number on or shutting off gas to the grill. W10118099 must be used. Follow instructions included with kit. A B C A. Gas supply line B. Shutoff valve “open” position C. To grill LP Gas Conversion Using a Local LP Gas Supply Conversion must be made by a qualified person. The installation of this grill must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code, ANSI Z223.1/NPFA 54, Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.2. A B CD A. Grill gas pipe B. New CSA International approved “outdoor” flexible gas supply line C. Rear of grill D. To local LP gas supply LP Gas Conversion Using a 20 lb LP Gas Fuel Tank To convert to LP gas, the LP Gas Conversion Kit Part Number W10118099 must be used. Follow instructions included with kit. A 20 lb LP gas fuel tank must be purchased separately. INSTALLATION INSTRUCTIONS Unpack Grill WARNING 3. Remove foam block and wrap from inside the grill. Excessive Weight Hazard Use two or more people to move and install grill. Failure to do so can result in back or other injury. ¦ Unpack grill. Remove all packaging materials and remove grill from carton. ¦ Move grill close to desired outdoor location. ¦ Open the hood. Remove Packaging Material Inside the Grill A B A. Foam block B. Foam wrap 1. Cut the tiedowns holding the grates together. 2. Remove rotisserie skewer (on some models), warming shelf 4. Replace the grill grates. and grill grates from inside the grill and remove packaging 5. Place warming shelf on brackets as shown. material. A B A A. Warming shelf brackets B. Warming shelf 6. On some models, install rotisserie mounting bracket using 2 screws. A B A. 2 screws B. Rotisserie bracket 7. Dispose of/recycle all packaging material. Make Gas Connection NOTE: If grill has been converted to LP gas, follow instructions in “Conversion to LP Gas” at the end of this section. WARNING Fire Hazard Do not use grill near combustible materials. Do not store combustible materials near grill. Doing so can result in death or fire. Natural Gas Use The installation of this grill must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code, ANSI Z223.1/NPFA 54, Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.2. 1. Place grill into outdoor enclosure, but leave enough room in back to connect to gas supply and electrical plug-in. WARNING Explosion Hazard Use a new CSA International approved “outdoor” gas supply line. Securely tighten all gas connections. Failure to do so can result in death, explosion, or fire. 2. Make gas connections. A combination of pipe fittings must be used to connect the grill to the existing gas line. ¦ If local codes permit, use an outdoor flexible stainless steel tubing gas connector, design-certified by CSA International, to connect the grill to the rigid gas supply line. A ..." diameter line is recommended. Using a wrench to tighten, connect the gas supply to the grill. Use pipe- joint compound on all non-flared male threads. Do not kink or damage the flexible connector when moving the grill. ¦ Pipe-joint compounds suitable for use with Natural gas must be used. Do not use Teflon® tape. A B CD A. Grill gas pipe B. New CSA International approved “outdoor” flexible gas supply line C. Rear of grill D. To Natural gas supply 3. Open the manual shutoff valve in the gas supply line. The valve is open when the handle is parallel to the gas pipe. A B A. Closed valve B. Open valve 4. Test all connections by brushing on an approved noncorrosive leak-detection solution. Bubbles will show a leak. Correct any leak found. Plug in Grill 1. This built-in outdoor grill comes with a 5,000 mAmp power transformer plug assembly for the grill lights and igniter. Plug in the single-prong plug in the receptacle on the left underside of the grill. A. Single-prong plug WARNING WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 2. Plug into a grounded 3-prong outlet. 3. Gently slide grill completely into outdoor enclosure. 4. Now go to the “Check and Adjust the Burners” section. Conversion to LP Gas (If LP ...

Herunterladen

Geben Sie zwei Ziffern: