Stimmen - 4, Durchschnittliche Bewertung: 4.8 ( )

Hersteller: Dynasty Stoves Dateigröße: 1.18 mb Dateiname: Dynasty_manual.pdf Unterrichtssprache:

Safety SAVE THIS MANUAL FOR FUTURE REFERENCE 5 installation installation INSTALLATION OF YOUR DYNASTY GRILL Safe and satisfactory operation of your Dynasty grill depends qualified installers and service technicians. This is upon its proper installation. The installation, adjustments and necessary to insure proper operation and also to prevent service of your Dynasty grill must be performed only by accidents. Location When determining a suitable location take into account concerns such as exposure to wind, proximity to traffic paths and keeping any gas supply lines as short as possible. Locate the grill only in a well ventilated area. For free standing models allow 12" from the sides and rear to adjacent combustible construction. Built-in Installation Your Dynasty grill is designed for easy installation into a non-combustible enclosure. The supporting deck and counter must be level and flat. When determining the final location for your grill it is required that ventilation holes be provided in the enclosure so that gas will not become trapped in the event of a leak (See page 9). When installing your Dynasty grill in a combustible enclosure, it is necessary to use a suitable insulated jacket or sleeve; follow cabinet cut out dimensions as shown on page 7. Use only an insulated jacket or sleeve manufactured by Jenn-Air. Built-in Design Models If using a rear wall, locate the weather proof electrical outlet on the left-hand side for the rotisserie motor. The rotisserie motor requires a 110/120 VAC supply. The power supply cord on the motor is equipped with a 3 prong (grounded) plug for protection against shock hazard. Do not cut or remove the grounding prong from the plug. NOTE: See dimension tables in page 7 referring to figure below. When installing a grill, side burner, or bartender on a cabinet with bullnose, dimension "A" is the width of appliance plus 1/8 clearance. 6 3 PRONG PLUG 4 X 4 MIN. OPENING FOR BOTTOM GAS CONNECTION 4 X 4 MIN. OPENING FOR REAR GAS CONNECTION 7 installation DYNASTY CUT OUT DIMENSIONS FOR GAS GRILL AND ACCESSORIES Installation DSBA DBQ DBTA DWD-30 DADA DSDA DYNASTY BAR TENDERS A=B C D DBTA - 13 12 24 1/2 11 1/4 (30 cm) (62 cm) (28.5 cm) DBTA - 18 17 1/8 24 1/4 9 3/4 (43 cm) (62 cm) (25 cm) DBTA - 30 29 1/8 24 1/4 9 3/4 (74 cm) (62 cm) (25 cm) MODELS NON COMBUSTIBLE COMBUSTIBLE A B C D A=B C D DBQ30 30-1/8 29 24-1/2 11-1/4 29-7/8 25-1/8 12-1/4 (76.5 cm) (73.6 cm) (62 cm) (28.5 cm) (75.8 cm) (64 cm) (31 cm) DBQ42 42-1/8 41 24-1/2 11-1/4 41-7/8 25-1/8 12-1/4 (107 cm) (104 cm) (62 cm) (28.5 cm) (106 cm) (64 cm) (31 cm) DBQ55 55-1/8 55-1/8 25-1/8 11-1/4 54-7/8 25-1/8 12-1/4 (140 cm) (140 cm) (64 cm) (28.5 cm) (139 cm) (64 cm) (31 cm) DYNASTY BUILT-IN GRILLS DYNASTY WARMING DRAWER E F DWD-30 28 1/4 9 3/4 (71.75 cm) (24.75 cm) Note: Minimum depth 21 (53 cm) DYNASTY ACCESS DOORS E F DADA - 18 16 1/4 19 3/8 (41.25 cm) (49 cm) DADA - 30 28 1/4 19 3/8 (71.75 cm) (49 cm) DADA - 42 40 1/4 19 3/8 (102.25 cm) (49 cm) DYNASTY SIDE BURNERS A=B C D DSBA-1 12 24 1/2 11 1/4 (30.5 cm) (62 cm) (28.5 cm) DSBA-2 12 24 1/2 11 1/4 (30.5 cm) (62 cm) (28.5 cm) DYNASTY STORAGE DRAWERS E F DSDA-2 12 1/8 19 (30.75 cm) (48.25 cm) DSDA-3 12 1/8 19 (30.75 cm) (48.25 cm) Note: Minimum depth 21 (53 cm) DSDA DADA DWD-30 DSBA DBQ DBTA NOTE: See previous page for location of dimensions installation installation INSTALLATION OF YOUR DYNASTY GRILL (continued) Gas Requirements Your Dynasty grill is designed to work with Natural or Propane Gas. Check your rating plate to make sure the gas supply provided is the gas type listed on the rating plate (see page 3). An installer supplied gas shut-off valve must be located in an easily accessible location. Use only pipe sealant that is an approved type and is resistant to the actions of propane gas. IMPORTANT: Your Dynasty grill must use the gas type specified unless converted by an authorized servicer using factory parts. IMPORTANT: All plumbing must comply with applicable codes (see page 2). TYPICAL BOTTOM GAS CONNECTION REGULATOR STREET ELBOW MANIFOLD PIPE ELBOW MAY BE ROTATED FOR REAR GAS CONNECTION AS SHIPPED FROM INSTALLER SUPPLIED SHUT OFF VALVE IN ACCESSIBLE LOCATION FACTORY • Typical Natural Gas Hook Up 9 • Typical Propane Gas Connection Installation • Typical Propane Self Contained Connection FLIP CAP FOR PROPANE GAS PLUMBED IN CONNECTION ELBOW MAY BE ROTATED FOR REAR GAS CONNECTION CUSTOMER SUPPLIED GAS SHUT OFF VALVE REMOVE CONVERTIBLE REGULATOR. INSTALL FLARE ELBOW INCLUDED IN KIT. REGULATOR WITH HOSE. FOR SELF-CONTAINED OPERATION PROVIDED IN KIT. 20 LB (5 GALLON) PROPANE CYLINDER DO NOT PLACE MORE THAN ONE CYLINDER IN THE ENCLOSURE AT ANY TIME. CYLINDERS THAT ARE NOT CONNECTED FOR USE SHALL NOT BE STORED IN THE VICINITY OF THIS OR ANY APPLIANCE installation installation installation NOTE: An enclosure for a propane gas cylinder shall be vented by openings on the level of the cylinder valve and at floor level. The effectiveness of the opening(s) for purposes of ventil...

Herunterladen

Geben Sie zwei Ziffern: