Stimmen - 3, Durchschnittliche Bewertung: 5 ( )

Hersteller: Dacor Dateigröße: 6.02 mb Dateiname: 02254120e.pdf Unterrichtssprache:

. There shall be a minimum clearance of 2 inches (51mm) between the floor of the LP-gas cylinder enclosure and the ground. • The design of the outdoor cooking enclosure must allow the LP-gas cylinder to be connected, disconnected and the connections inspected and tested outside the cylinder enclosure. • Connections which may be disturbed when installing the cylinder in the enclosure can be leak tested inside the enclosure. • Internal mounting means shall be provided on the outdoor gas grill for mounting the LP-gas supply cylinder. If the outdoor grill is not in use, the gas must be turned off at the supply cylinder. Rotisserie mounting bracket (factory installed) Junction Box Trim frame (accessory) 3/4" (19mm) min. to any material* 1/4" (6mm) 1 1/4" (32mm) 10" (254mm) Min. to combustibles 1 1/4" (32mm) Min. to non-combustible 28 1/2" (724mm) To finished countertop 23 3/4" (603mm) 24" (610mm) Junction Box Trim frame (accessory) 3/4" (19mm) Min. to any material* 10" (254mm) Min. to combustibles 2" (51mm) Min. to non-combustible 1/4" (6mm) 23 3/4" (603mm) 24" (610mm) See page 8 for overall cabinet dimensions. See page 8 for overall cabinet dimensions. OB36, OBS36, OB52 and OBS52 Cutout Dimensions - Side View OBSB162 Cutout Dimensions - Side View 8 Planning the Installation Location Planning - Enclosed Cabinets (continued) 3/8" (10mm)o Both sides 6" x 7" (152mm x 178mm) utility cutout Coutertop 25" (635mm) 24" (610mm) 8" (203mm) Min. to combustibles above the countertop surface, both sides 1 1/2" (38mm) 12 1/4" (311mm) 2" (51mm) OB(S)36 - 33 1/2" (851mm) OB(S)52 - 49 1/2" (1257mm) 6" x 6" (152mm x 152mm) utility cutout for OBSB162 3/4" (19mm) Min. to any material for ventilation 9" (228mm) Max. OB(S)36 - 36 1/2" (927mm) OB(S)52 - 52 1/2" (1334mm) OBSB162 16 1/8" (410mm) 36" (914mm) Cutout Dimensions - Top View Cutout Dimensions - Front View OBAD 36 Accessory doors shown Accessory Door Cutout Dimensions Dimension Cutout Width OBAD20: 16 3/4” (425mm) OBAD36: 33 1/8” (841mm) Cutout Height 18 3/4” (476mm) Cutout Depth 3” (76mm) 9 Planning the Installation Location Planning - Cart Installations Example of Grill Cart Location • Maintain all minimum clearances shown between the appliance and all surfaces behind and to the side of the appliance. • Allow 26 inches minimum in front to open and close the cabinet drawers. • For proper grill and drawer operation, use the outdoor grill and cart only on a level surface. • Side distances exclude optional shelves. Above the cooking surface, both sides: 1 1/4” (32mm) Min. to non-combustibles 10” (254mm) Min. to combustibles Above cooking surface, behind unit: 2 1/2” (64mm) Min. to non-combustibles 11 1/4" (286mm) Min. to combustibles (with hood in closed position) Above the cooking surface, both sides: 1 1/4” (32mm) Min. to non-combustibles 10” (254mm) Min. to combustibles Above the cooking surface, behind unit: 2 1/2” (64mm) Min. to non-combustibles 11 1/4” (286mm) Min. to combustibles (with hood in closed position) 10 Parts List Models OB36, OBS36, OB52 and OBS52: A Drip tray G Rotisserie rod and forks B Smoker box H Rotisserie motor C Warming rack J Light lens pry stick D Regulator assembly Match holder E Grills Cleaning cream F Flame spreaders Models OB52, OBS52 and OBSB162 K Side burner grate M Side burner heads (2) L Side burner cover N Side burner caps (2) LP Models equipped for use with an LP cylinder: P 3/4” coupling R 3/4” nipple Installation Instructions warning • Before installing the appliance, make sure the electrical and gas (on tank-less installations) service meets the requirements specified in the Planning the Installation section of this manual. • This appliance must be installed by a licensed plumber or gas fitter when installed within the Commonwealth of Massachusetts. • Excessive weight warning: Since the appliance and grill cart are heavy, install the appliance with the help of at least one other person. • Make sure the power cord is NOT connected to the electrical outlet while connecting the gas line to the appliance. • Do not apply excessive pressure when tightening connections and fittings. • Do not use plumber’s putty or Teflon tape on gas compression connections. Doing so can defeat the proper sealing of these fittings. • Use only approved gas line thread compound or tape to seal gas connections. • The maximum gas supply pressure to the regulator must not exceed 1/2 pound per square inch. Preparing for Installation 1. Before removing the unit from the box, check the labeling on the box to make sure that the appliance is equipped for the gas type to be used. Liquid petroleum (propane) units are identified by the “LP” designation at the end of the model number. Do not proceed with installation if you do not have the correct model. Conversion in the field from one gas type to another is not permissible. 2. With the help of an assistant, remove the appliance and all the parts from the box. Check to make sure all parts are included. 3. Remove all shipping ...

Herunterladen

Geben Sie zwei Ziffern: