Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Brinkmann Dateigröße: 13.08 mb Dateiname: Unterrichtssprache:

WARNING: We recommend and request that you do not remove the control panel in order to access the valve tips. If you choose to remove the control panel, you must replace the control panel bezels exactly as illustrated in Figure 2. Failure to replace the bezels as illustrated could lead to personal injury and/or property damage. Step 7 Carefully replace each burner, making sure burner openings slide over valve nozzles. Screw each main burner "foot" down using screwdriver and screws that were set aside in Step 3. Step 8 Replace warming rack, cooking grills, heat shields and grease tray. Note: Follow directions in the leak testing section of this manual before using this grill. CONVERSION INSTRUCTIONS 810-9520-S CAUTION: Some parts may contain sharp edges. Wear protective gloves if necessary. WARNING: Only use the specific orifice designated for your grill model. Always double check the millimeter size on the side of the orifice tip prior to installation. Use of any other orifice could lead to personal injury, property damage and void your grill warranty. Note: Make sure all control knobs are in the off position, LP tank valve is closed and tank is disconnected from regulator and removed from grill. Step 1 Using an adjustable wrench to hold the gas manifold connection secure, use a 3/4” wrench to loosen the hose connection nut. Replace existing LP hose/regulator assembly with natural gas 10’ hose assembly. Tighten the connection carefully using two wrenches. Step 2 Remove cotter pin from side burner "foot". Carefully lift side burner up and away from valve nozzle. Set aside for later use. Gas Manifold Nut 10’ Natural Gas Hose Warming Rack Cooking Grills Heat Shields Cotter Pin Step 3 Open hood and remove warming rack, cooking grills and heat shields. Set aside for later use. Side View LP Gas Orifice Firebox Front Panel Gas Orifice Tool Step 4 Remove screw from each burner "foot" using a screwdriver. Carefully lift each burner up and away from valve openings. Set aside for later use. Step 5 Use the gas orifice tool to remove the LP brass orifice from main burner valves through the hole on the firebox front panel. Repeat this step for all main and side burner valves in your grill. The side burner valve orifice is under the side shelf. Note: All orifices of the grill, except rotisserie, are double orifices type (LP gas and natural gas).You only remove the LP gas orifice tip. CAUTION: Some parts may contain sharp edges. Wear protective gloves if necessary. Step 6 Remove all the control knobs from the control panel and set aside for later use. Step 7 Figure 1 shows valve stem and bezel with the control knob removed. Take five large stop plates from the component card and place them over the valve stems as illustrated (Figure 2). Verify the tab and the stamped letter on the stop plates face out. Replace control knobs when finished. WARNING: We recommend and request that you do not remove the control panel in order to access the valve tips. If you choose to remove the control panel, you must replace the control panel bezels exactly as illustrated in Figure 2. Failure to replace the bezels as illustrated could lead to personal injury and/or property damage. Step 8 Carefully replace each burner, making sure burner openings slide over valve nozzles. Screw each main burner "foot" down using screwdriver and screws that were set aside in Step 4. Step 9 Replace warming rack, cooking grills, heat shields and grease tray. Note: Follow directions in the leak testing section of this manual before using this grill. Stop Plate Tab Stop Pin Figure 1 Figure 2 Warming Rack Cooking Grills Heat Shields CONNECTING YOUR GRILL TO THE NATURAL GAS SOURCE 1. Coat pipe nipple with gas resistant teflon tape or pipe dope. Tighten quick-disconnect coupling onto pipe nipple that leads to natural gas supply (Figure A). 2. After grill is completely assembled, make sure natural gas supply valve is “OFF” and then connect natural gas hose to socket. Push sleeve back on socket (Figure B) and insert plug until sleeve snaps forward, locking plug into socket. Be sure to leak test these connections prior to use. Insert cover when hose is disconnecte...

Herunterladen

Geben Sie zwei Ziffern: