Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Broilmaster Dateigröße: 9.89 mb Dateiname: Unterrichtssprache:

Carefully thread the end of the ignitor wire through the center hole in the grill bottom. Slide the ground lug over the ignitor wire and fasten with nut provided. Attach one end of the ground wire to the terminal on the rear of the electronic ignitor. Attach the remaining end to the ground lug. See Figures 8 and 9. Attach ignitor wire to the spark terminal on the rear of the electronic ignitor. Ignitor Assembly Slide the collector box spacer and nut (provided on assembly) onto the collector box shaft and tighten. See Figure 8. Note: Peel protective film from control panel label before installing ignitor. Nut Figure 8 Figure 9 B101623-2-0112 GRILL ASSEMBLY Radiation/Wind Shield Place the radiation/wind shield in the grill bottom. See Figure 10. Burner Assembly 1. Place the Burner Body, with the ports facing up, on a flat surface. 2. Place the Gasket on the Burner Body, aligning the holes. 3. Set the Venturi Assembly on the Gasket again aligning the holes. See Figure 11. 4. Align hole on burner bracket with the left front hole on Venturi Assembly as shown in Figure 11. 5. With all holes properly aligned, using four #10 x 1/2 Phillips Truss Head Screws, attach the Venturi Assembly to the Burner Body. See Figure 11. Do not tighten the screw securing the burner bracket to the venturi assembly. “P”series“H”series Figure 10 Figure 11 B101623-2-0112 6. The burner bracket should be at a slight angle as shown in Figure 12. Once the proper angle is achieved, tighten the screw securing the burner bracket to the venturi assembly and burner body. 11° “H”SERIES BURNER SHOWNCL “H” Series Burner Shown Figure 12 7. Insert the 1/4-20 x 1 1/2 Phillips Truss Head Screw from the underside of the grill and secure with the 1/4-20 Hex Nut. See Figure 13. Figure 13 Installing the Burner 1. Insert the burner assembly into the grill bottom with the venturi tubes facing the front of the grill. See Figure 14. Figure 14 Note: If the Grill Head is installed on a PCB1 or DCB1, make sure the cart shield is not installed until the burner bracket is mounted. 2. Slide the venturi on to the valve assembly. 3. Raise the unsecured end of the burner bracket and slip it over the 1/4-20 x 1 1/2 Phillips Truss Head Screw as shown in Figure 15. The screw will fit into the hole on the burner bracket. “P” Series Shown Figure 15 B101623-2-0112 4. Slide the bridge pin through the hole in the 1/4-20 x 1 1/2 Phillips Truss Head Screw as shown in Figure 16. Figure 16 Handle For your added comfort a foam grip has been provided. See Figure 17. Tip: For ease of installation, slightly lubricate the front handle with liquid soap before pushing the foam grip into place. Fasten the front handle to the grill lid with two #10-24 x 1" screws. See Figure 18. Figure 17 Figure 18 Install side shelves or side burner to side of grill at this time. Reinstall grill top to grill bottom with 2 pins and clips removed in Figure 4. B101623-2-0112 GRILL ASSEMBLY Lid Stop Attach the lid stop assembly to the grill bottom as shown. See Figure 19. Note: H3X/H4X Series grills do not come with a Lid Stop Kit. The Lid Stop Kit is available as an accessory. Installing Flare Busters Place the briquet rack in the grill. Position the flare busters as shown in Figures 20a and 20b. Figure 19 P3X Figure 20a P4X Figure 20b B101623-2-0112 GRILL ASSEMBLY Installing Racks Place the briquet rack or on the burner assembly. Position the flare busters on the briquette rack or the ceramic briquets evenly on the briquette rack without overlapping. See Figures 20a and 20b. For Smoker Shutter installation see DPA100 manual included with your P3SX grill. Set the multilevel cooking grids. See Figures 21a and 21b. Installing Char-Master Briquets Individually place the ‘Char-Master’ briquets in a single layer evenly on your grill’s briquet rack; DO NOT dump them onto the briquet rack. A single layer of ‘Char-Master’ briquets is all that’s needed. DO NOT overlap or stack the briquets. See Figure 21b. After properly placing the ‘Char-Master’ briquets on your grill’s briquet rack, there may be some briquets left over. Save them for future use. Before cooking, always preheat the grill as directed by the grill’s operating instructions. Hot briquets cause better, quicker cooking and better flavor. Cleaning Routine preheating and routine burn-off (also called post-heating) of a grill will clean the ‘Char-Master’ briquets. Periodically turn the briquets over while they are cool. Note for H3 Package Owners: The side shelf must be installed before installing the Briquets and Briquet Rack. Figure 21a Figure 21b B101623-2-0112 OPERATION - PROPANE & NATURAL GAS GRILLS Checking for Gas Leaks Check for gas leaks every time you connect your Broilmaster® propane gas grill to a Propane gas cylinder, when a connected cylinder has not been used recently, or when either a natural or propane grill is being used for the first time. Caution: Do not use an open flame when checking for leaks. Checking for leaks with an open flame may l...

Herunterladen

Geben Sie zwei Ziffern: