Stimmen - 4, Durchschnittliche Bewertung: 3 ( )

Hersteller: Coleman Dateigröße: 1.05 mb Dateiname: Unterrichtssprache:

Natural gas flex line must be purchased separately based on the distance of your grill location from the natural gas line. Please be sure to check the size of your home’s natural gas line fitting to make sure you get the right size connection for your particular application. If you have questions, please consult your local natural gas distributor or qualified service technician. 9 Grill Assembly — 8350 Series IMPORTANT: Remove all protective plastic film from stainless steel parts prior to assembly/use. This film is installed at the factory to prevent damage that could occur during shipment and handling. Interior Parts Installation 1. Insert the row of four heat tents with the triangle ridges facing up (Fig. 1). 2. Install the four cooking grates on the ledges provided on the grill to create your cooking surface (Fig. 2). 3. Place the warming shelf on the support brackets. The end support rods slip inside the slots in the support brackets (Fig. 2). 4. Remove the label from the drip tray. Open the door and install the drip tray by sliding it into position as shown (Fig. 3). The drip tray is located underneath the grill, inside the storage compartment. Igniter Battery Installation 1. The AA battery, spring and igniter cap must be installed before using (Fig. 4). 2. Install the AA battery, negative end first. 3. Slide the spring assembly over the battery. 4. Screw the igniter cap onto the igniter (Fig. 5). Test the Igniter: A spark should appear at electrode tips. If the spark does not appear: -Check the wire connections to the electrode module. -Check the proper assembly of a fresh AA battery. Fig. 4 Fig. 5 Fig. 1 Fig. 2 Fig. 3 10 LP Cylinder Conversion — 8350 Series NOTE: This step applies to you only if you are converting your 8350 Series grill to use LP GAS. If you will be using your grill with NATURAL GAS, this section does not apply to you. Please skip back to the section titled “Natural Gas Installation - 8350 Series ”. The 8350 Series grill is set up from the factory to use NATURAL GAS. If you want to use LP GAS, you must purchase the LP GAS CONVERSION KIT (sold separately). Follow the installation instructions provided with the LP GAS CONVERSION KIT. LP GAS CONVERSION KIT (not shown) Part Number Description 9992-258 8350 Series Natural Gas to LP Conversion Kit LP Cylinder Installation 1. Set the LP Cylinder in the Cylinder Support location with the outlet valve facing toward the right side of the grill (Fig. 6 and 7). 2. Insert the TYPE 1 Nipple of the regulator into the cylinder’s Fuel Valve Outlet as shown. Turn the regulator hand wheel clockwise to tighten. No tools are needed. The hand wheel will come to a complete stop when the connection is secure, and the gas will not flow until a positive seal is achieved. Fig. 6 IMPORTANT! TO ENSURE PROPER GAS FLOW, BURNER CONTROL VALVES MUST BE “OFF” BEFORE OPENING THE GAS CYLINDER VALVE. Fig. 7 WARNING: During assembly of the grill and when attaching or replacing the L.P. gas cylinder, insure that the gas supply hose is free of kinks and/or damage and is at least 3 inches away from hot surfaces such as the grill casting. 11 Portable L.P.Gas Barbecue Cylinders Liquefied Petroleum gas (abbreviated L.P. gas or propane), is highly flammable. It becomes liquid when stored under high pressure inside a cylinder and vaporizes when released. L.P. gas is heavier than air and tends to collect in low areas. It is important that there are no leaking connections on your gas grill that could cause a fire or explosion (see the section titled “LEAK TESTING”). Portable LP gas grills require a fuel delivery system which is comprised of a valve [A], a hose [B], a regulator [C] with vent hole [G], an L.P. gas supply cylinder [D], a Type 1 coupling nut [E] and a Type 1 cylinder valve [F], (Fig. 8). Illustration in (Fig. 8) is for description purposes only. The valve assembly for this grill is of a different configuration. WARNING Your new barbecue grill is equipped with a Type 1 coupling nut [E]. DO NOT attempt to connect to any other L.P. cylinder not equipped with a mating Type 1 cylinder valve [F]. This grill is not to be used with any other cylinder connection device. A B C E Fig. 8 D F G 12 L.P.Gas Cylinder DANGER • DO NOT insert any foreign objects into the valve outlet. You may damage the valve. A damaged valve can cause a leak, which could result in explosion, fire, severe personal injury or death. WARNING • Cylinders must be stored outdoors out of the reach of children and must not be stored in a building, garage or any other enclosed area (Fig. 9). Cylinder Specifications • Any L.P. gas supply cylinder used with this grill must be approximately 12 inches diameter and 18 inches high. The maximum fuel capacity is 80% and is approximately 20 pounds of propane. • The maximum weight of a properly filled cylinder will be approximately 38 pounds (47.7 lbs. nominal water capacity). • The L.P. cylinder must have a shut-off valve terminating in a Type 1 L.P. gas cylinder valve o...

Herunterladen

Geben Sie zwei Ziffern: