Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Coleman Dateigröße: 2.19 mb Dateiname: Unterrichtssprache:

• Read labels on the L.P. Gas Supply Cylinder. • New cylinders are always shipped empty for safety. • Allow only qualified L.P. gas dealers to fill or repair your L.P. gas supply cylinder. • Inform the gas dealer if it is a new or used cylinder to be filled. • Caution the gas dealer not to overfill cylinder. • After filling, have the gas dealer check for leaks and to see that the relief valve remains free to function. CAUTION Have the gas dealer weigh cylinder after filling to ensure that the cylinder is not overfilled. Hose and Regulator The Type 1 connection system has the following features: 1.The system will not allow gas to flow until a positive connection has been made. NOTE: The cylinder control valve must be turned off before any connection is made or removed. 2.The system has a thermal element that will shut off the flow of gas in the event of a fire. 3.The system has a flow limiting device which, when activated, will limit the flow of gas to 10 cubic feet per hour. 4.NEVER use grill without leak testing this connection. WARNING • DO NOT attempt to adjust the regulator as this could create a situation causing personal injury or property damage. The pressure regulator and hose assembly with the Type 1 fitting supplied with the appliance must be used. Do not use another hose and regulator assembly other than the one supplied with the grill or a Coleman replacement pressure regulator assembly. The pressure regulator and hose assembly provided is factory set at an outlet pressure of 11 inches water column (1/2 psi). • Keep the small vent hole in the regulator clean of dirt and debris (see item [G], Fig. 10, pg. 4). • Consult your L.P. gas dealer if you think the regulator is not working properly. WARNING During assembly of grill and when attaching or replacing the L.P. gas cylinder, insure that the gas supply hose is free of kinks and/or damage and is at least 3" away from hot surfaces such as the grill housing. Transporting the Cylinder • Transport only one cylinder at a time. • Transport cylinder in an upright and secure manner with a control valve turned off and the cap in place. • DO NOT transport cylinder in passenger compartment, unless you have an open window ventilation. • DO NOT leave cylinder in direct sunlight or in a high heat area such as a closed car trunk. High heat areas could cause the relief valve to vent gas. • Use a cylinder cap on cylinder valve outlet during transport and when the cylinder is not connected to grill. • Keep cylinder valve closed when not in use. • Take the cylinder directly home after it has been filled. 5 To Set Up Step 1 ¦ Carefully read and follow the instructions for proper setup & use of your Coleman® Event Grill. Step 3 ¦ Attach Leg Brace as shown. CAUTION Because of its size and weight, it is recommended that there are at least two (2) people available to set up this grill. ¦ See replacement parts list for parts identification. Step 2 ¦ Unlock Grill Legs as shown. ¦ Carefully lower both Left and Right Grill Legs into the locked position. LEG BRACE Step 4 ¦ Unlock both Left and Right Lower Tank Mounts. ¦ Place a 20 lb. propane cylinder in both Lower Tank Mounts and secure as shown. For easier installation, place the tank with the collar opening toward the grill, lower the upper tank support, then rotate the tank to engage the upper tank support. NOTE: Grill may be operated with only one cylinder. Step 5 ¦ Remove both Regulators from bottom of grill. ¦ Attach Regulators to Propane Cylinder Connections and hand-tighten. 7 To Set Up continued Step 6 CENTER LIDLEFT LID (SHELF) RIGHT LID (SHELF) ¦ Unlock Right Side Lid. NOTE: Undo latches on front and back of lid. ¦ Release flaps to form Right Side Shelf. LID FLAPS IMPORTANT: Always remove Lids in this order: • Right Lid first. • Left Lid second. • Center Lid last. ¦ Carefully insert Shelf Lip on Right Side Shelf into Top Channel, while at the same time making sure the Notches on the side Flaps fit into the Flanges on the grill body. To Set Up continued Step7 ¦ Install two Grease Pans from front as shown. Step 7 ¦ Install 9-Volt Battery with positive (+) terminal as shown on Igniter Module. Leak Testing Igniter Module NOTCH FLANGE TOP CHANNEL SHELF LIP DETAIL “A” DETAIL “B” 8 FLANGE SHELF LIP DANGER TO PREVENT FIRE OR EXPLOSION HAZARD: • NO SMOKING. DO NOT use or permit sources of ignition in the area while doing a leak test. • Perform leak tests outdoors only. • NEVER perform a leak test with fire or flame. How to Check for Leaks 1. Make a soapy solution of equal parts mild liquid dishwashing detergent and water. 2. Turn off all burner control knobs. 3. Turn on fuel supply. Turn cylinder valve knob counterclockwise (right to left) one rotation. 4. Apply soap solution to connections indicated with arrows in Fig. 15. If bubbles appear at these areas, a leak is indicated. 15 ¦ Repeat the same order for attaching the Left Side Shelf as you did on the Right Side Shelf. ¦ Remove Center Lid and set aside until ready for...

Herunterladen

Geben Sie zwei Ziffern: