Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
4 5 The pressure regulator and hose assembly with the Type 1 fitting supplied with the appliance must be used. Do not use another hose and regulator assembly other than the one supplied with the grill or a Coleman® replacement pressure regulator assembly. The pressure regulator and hose assembly provided is factory set at an outlet pressure of 11 inches water column (1/2 psi). • Keep the small vent hole in the regulator clean of dirt and debris (see item [G], Fig. 1). • Consult your L.P. gas dealer if you think the regulator is not working properly. WARNING • DO NOT attempt to adjust the regulator as this could create a situation causing personal injury or property damage. WARNING During assembly of the grill and when attaching or replacing the L.P. gas cylinder, insure that the gas supply hose is free of kinks and/or damage and is at least 3 inches away from hot surfaces such as the grill housing. Hose and Regulator Transporting the Refillable Cylinder • Transport only one refillable cylinder at a time. • Transport the cylinder in an upright and secure manner with a control valve turned off and the cap in place. • DO NOT transport the cylinder in the passenger compartment, unless you have an open window ventilation. • DO NOT leave the cylinder in direct sunlight or in a high heat area such as a closed car trunk. High heat areas could cause the relief valve to vent gas. • Use a cylinder cap on the cylinder valve outlet during transport and when the cylinder is not connected to the grill. • Keep the cylinder valve closed when not in use. • Take the cylinder directly home after it has been filled. The Type 1 connection system has the following features: 1. The system will not allow gas to flow until a positive connection has been made. NOTE: The cylinder control valve must be turned off before any connection is made or removed. 2. The system has a thermal element that will shut off the flow of gas in the event of a fire. 3. The system has a flow limiting device which, when activated, will limit the flow of gas to 10 cubic feet per hour. 4. NEVER use grill without leak testing this connection. WARNING Handle a full cylinder with care. Gas is under high pressure. DANGER • NEVER store a spare L.P. gas supply cylinder under the grill body or inside the grill enclosure or in the vicinity of any heat producing appliance. (Fig. 3) • NEVER fill the cylinder beyond 80% full. Failure to follow this information exactly could result in an explosion and/or fire causing death or serious injury. Transporting the Refillable Cylinder (continued) Fig. 3 REPRESENTATIVE ILLUSTRATION 1 3 7 4 2 1. Grill Hood 2. Thermometer 3. Hood Handle 4. Side Shelf 5. Electronic Igniter 7. Cart with Doors 8. 120 VAC Electrical Outlet 9. 120 VAC Electrical Cord Inlet 10. Grilling/Cooking Surface 11. Warming Shelf Grill Features — 9993 Series 11 4 6 5 89 10 Fig. 6 Fig. 5 Fig. 4 1 3 7 4 2 1. Grill Hood 2. Thermometer 3. Hood Handle 4. Side Shelf 5. Electronic Igniter 7. Cart with Doors 8. 120 VAC Electrical Outlet 9. 120 VAC Electrical Cord Inlet 10. Grilling/Cooking Surface 11. Warming Shelf Grill Features — 9993 Series 11 4 6 5 89 10 Fig. 6 Fig. 5 Fig. 4 6. Control Knobs NOTE: See your dealer for Side Solution™ accessories that are purchased separately. 6 Special Unpacking Instructions - 9993 Series 5. Remove two screws at location “E” with a “Phillips” screwdriver (Fig. 9). Read All the Unpacking Instructions before starting this section! 1. Cut the shipping straps and remove the top of the cardboard container. 2. Remove the door assemblies that are located in the protective packing on each end of the grill. Set the doors aside for a later assembly step. 3. Lift the cardboard container sides from the shipping base. Additional boxes of parts are located inside the grill cart (Fig. 7). Fig. 9 E E 6. Remove the left side panel and set aside for a later assembly step (Fig. 10). Fig. 7 4. Remove boxes “A and “C” out the front door opening (Fig. 8). A C B D Fig. 8 C B Fig. 10 7. Remove the remaining large boxes and the grill hood (Fig. 11). Fig. 11 8. Replace the left side panel and tighten the two screws (Fig. 12). Fig. 12 7 Parts Identification - 9993 Series Fig. 13 8 IMPORTANT: Remove all packing material prior to assembly/use. If your grill has stainless steel components, remove all protective plastic film from stainless steel parts prior to assembly/use. This film is installed at the factory to prevent damage that could occur during shipment and handling. Grill Assembly Assemble the Wheels 1. Place part of the shipping carton behind the grill for protection. Lay the grill on its back to assemble the four wheels (Fig. 14). 2. Assemble the locking wheels at the front of the grill. Secure each wheel with four screws each. 3. Carefully lift the grill cart upright onto the wheels. Fig. 14 Assemble the Wind Screen 1. Remove four screws at location “F”. These are the mounting screws for the windscreen (Fig. 15). Fig. 15 F 2. Attach the windscreen with ...