Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
• Also try placing a pan of water above the lit burner side to help meat retain its juices. Replenish water as needed. 29 Cleaning the Venturi WARNING Spider’s nests or wasp’s mud inside the venturi may cause fire at valve. If a fire occurs, immediately turn off gas supply at L.P. cylinder valve (see representative illustration in Fig. 22). If your grill is set up for use with Natural Gas, turn off gas supply at the system manual shut off valve. Note: Spiders and small insects can spin webs and build nests inside the venturi tubes. This especially occurs in late summer and fall before frost when spiders are most active. These nests can obstruct gas flow and cause a fire in and around the burner valves. Such a fire can cause operator injury and serious damage to the grill. To help prevent a blockage and ensure full heat output, clean and inspect venturi tubes often (once or twice a month). NOTE: Water or air pressure will not normally clear a spider web. Steps For Cleaning Venturi: 1. Remove burner from grill bottom. 2. Look inside lower end of venturi tubes for nests, webs or mud. 3. To remove the above obstructions, use an accessory flexible venturi brush or bend a small hook on one end of a 20-inchlong flexible wire such as the one shown in Fig. 23. 4. Inspect and clean the burner if needed. 5. Replace the burner assembly into the grill. 6. Make sure the valve orifices are inside the venturi tubes. 7. Secure burner back into grill bottom. 22 REPRESENTATIVE ILLUSTRATION 23 30 Cleaning and Maintenance CAUTION All cleaning and maintenance should be done only when grill is cool & with the fuel supply turned off at the cylinder. If your grill is set up for use with Natural Gas, turn off gas supply at the system manual shut off valve. Suggested Cleaning Materials: • Mild dishwashing liquid detergent • Hot water • Wire brush • Paper clip • Nylon cleaning pad • Soft brass-bristled brush • Putty knife • Scraper Component Cleaning: • BURNER: Wire-brush loose corrosion from burner exterior. Clean clogged gas port holes with an opened paper clip. Replace corroded or damaged burners that would emit excess gas. • STAINLESS STEEL: Clean with any multipurpose (low abrasive, no phosphorous) metal polish or stainless steel polish and a soft cloth to prevent marring or scratching the surface. NEVER USE OVEN CLEANER! • ORIFICES: Unscrew orifices from rear of valves (Fig. 24). Wash orifices in solvent and blow air through the small end holes. Carefully replace the orifices in valve when they are dry. Make certain that orifices are tightly reassembled. Cleaning and Maintenance cont. Moving and Storage CAUTION DANGER NEVER attempt to operate your grill without orifices in the valves. A serious and immediate fire hazard would result. • COOKING GRATES: Clean cooking grates with mild soap and hot water. Remove stubborn residue with a mild cleanser or scrub brush. Use a brass-bristle brush on porcelain-coated grates. DO NOT use a commercial oven cleaner. • PORCELAIN-COATED HEAT TENTS™: Wipe off grease residue using a cleaning pad and a brass-bristle brush to knock off residue. Use care not to damage porcelain finish. Replace heat tents to their correct position. • GRILL INTERIOR: Remove grates and porcelain heat tents. Scrape side with tools and remove excess grease and cooking residue. Orifices Valves REPRESENTATIVE ILLUSTRATION 24 A collision with the grill, as with any metal object, could cause injury. Use care when moving a portable gas grill. Moving the grill: • Move grill slowly. DO NOT run with or pull the grill behind you; it could hit you from behind causing injury. • DO NOT move the grill while it is lit or hot, or with objects on the cooking surface(s) or side table(s). After moving the grill: • Check all gas connections for leaks that could occur from the movement. • Check the venturi tubes to be sure they are still over the orifices. Steps to follow before storing grill: • Clean the grill. • Coat the burner lightly with cooking oil to retard rusting. • For outdoor use only. If grill is stored indoors, detach and leave cylinder outdoors. If left outdoors, turn off the fuel supply to the L.P. cylinder and cover the grill for protection from the weather. Grill covers may be purchased from a grill dealer or manufacturer. WARNING If the grill is not in use, the gas MUST be turned off at the fuel supply cylinder. Troubleshooting Problem: Burner will not light or has incomplete burner flame. Possible Causes and Solutions: 1. Make sure the 9-volt battery is fresh. 2. Check for spider webs or insect nest in venturi and clean venturi. 3. Lack of fuel. Check to see cylinder valve is open and cylinder has fuel. 4. Misalignment of venturi on orifices. Position venturi over orifices. 5. Burner ports, orifices, valves or hose have blockage. Clean the components. 6. If burner lights with match but not igniter, check ceramic electrode position in gas collector and condition of igniter wire and its connections. Perform igniter test and ...
Dieses Handbuch ist für folgende Modelle:Konvektionsöfen - 5100 LP (5.42 mb)