Stimmen - 4, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Figure 2 1. CHECKING FUEL AND PROPER ORIFICES: Your Fire Magic Sideburner is equipped with orifices for natural gas unless otherwise indicated. For propane gas, smaller orifices must be installed to avoid hazardous overheating. The orifice size for Natural Gas is #49 (drill size) and for Propane Gas, the orifice size is #56 (drill size). Check the orifice size by removing the burner cap (Item#9F) and the venturi tube (Item #9C) and looking down through the hole in the center (see Figure 2 for the location of the orifice). The drill size is stamped on the orifice. If the number is not visible you may have to remove the orifice (as detailed below) in order to read the number stamped on the side of the orifice. To remove or change an orifice, you need a 3/8" nut driver or small wrench. Loosen the orifice using the nut driver, approaching from above, or by approaching from underneath the burner using a small wrench. Remove (check the number on the side if needed) and replace with the correct sized orifice for your gas type. 2. CONNECTING THE GAS SUPPLY TO YOUR FIRE MAGlC SIDEBURNER: a. The burner manifold has a 3/8” male flare fitting gas inlet elbow. A 3/8" female flare fitting connector nut is required to hook the gas supply to the burner. b. Use a stainless steel flex connector to bring the gas supply from the gas line stub or propane gas tank to the sideburner manifold. A 3/8" x 24" or 36" flex connector is suitable for most installations. CAUTION: Use only a C.S.A. listed stainless steel flex connector. Do not use a rubber hose or plastic hose within the enclosure for your sideburner, it will leak resulting in an explosion and/or serious injury. NOTE: For installation in a portable barbecue cart, see the installation instructions packed with the sideburner shelf and connector kit. Also refer to the portable cart instruction section for attaching shelves. c. Be sure the gas supply is 'OFF'. Connect the pipe adapter fitting supplied with the flex connector to the gas supply stub. Use pipe joint compound which is resistant to all gasses on the pipe fitting. Tighten fitting to gas supply and connector flare nut securely. Note: pipe joint compound should not be used on flare fitting connections. 3 d. Connect the flex connector flare nut to the sideburner manifold elbow flare fitting. Be sure to tighten securely. Use a second wrench to support the manifold to avoid damaging the manifold. e. Check all gas connections for leaks with a brush and soapy water solution before lighting. NEVER USE A MATCH OR OPEN FLAME TO TEST FOR LEAKS. f. Lower the unit into the enclosure. Figure 3 3. POSITIONING THE BURNER CAP AND GRILL: Place the burner cap so it is centered over the burner. Be sure the notches in the burner cap fit over the studs protruding from the burner (see Figure 3). The burner cap and grill are coated with a high temperature porcelain finish that prevents rust and can be cleaned with oven cleaner. SAFETY TIPS IN USING YOUR SIDEBURNER: Each time you use your sideburner, ensure that: 1.The area around the unit is clear and free from flamable vapors, liquids and other combustable materials. 2.There is no blockage of air flow around the burner. 3. When using propane gas: a. The special ventilation openings in the enclosure are kept free and clear of debris. b. If connected to a propane cylinder, the rubber hose attached to the regulator is carefully inspected before each use. c. The propane cylinder, regulator and rubber hose are installed in a location not subject to heating above 125° F (51° C). 4. Burner flames are burning evenly around the burner cap with a steady flame (mostly blue with yellow tipping). PRESERVING YOUR SIDE BURNER FOR YEARS OF CAREFREE USE: The sideburner surfaces may be cleaned with any common acid free household cleaner. Occasionally remove the burner cap and, if necessary, use a soft, stiff brush (an old toothbrush) to clean the ports in the burner and the underside of the burner cap. CAUTlON: Never use acid chemicals or abrasive pads to clean porcelain or aluminum surfaces. Do not operate the burner with the cover closed. The valve, igniter and burner on your Fire Magic Sideburner have been pre-assembled and tested before shipping. We suggest you follow and practice these instructions for safe lighting of your Fire Magic Sideburner. CAUTION: DO NOT ALLOW A COOKING POT OR PAN TO GET TOO CLOSE TO OR COVER, THE IGNITOR OR FLAME ADJUSTMENT KNOBS DURING USE. OVERHEATING OF THE KNOBS WILL OCCUR, RESULTING IN DAMAGE AND POSSIBLE UNIT MALFUNCTION. IF THIS CAUTION IS NOT FOLLOWED. LIGHTING INSTRUCTIONS FOR AUTOMATIC LIGHTING: 1. Open the lid. 2. Make sure the control valve is in the 'OFF' position. 3. Open the propane gas tank valve or gas line valve. 4. Depress the control valve and turn to the 'HIGH' position. 5. Immediately press the spark generator button. The burner should light. 6. If the burner does not light, turn the control valve to the 'OFF' position and WAIT 5 MlNUTES. 7. Repeat ste...
Dieses Handbuch ist für folgende Modelle:Konvektionsöfen - 25326-016 (219.08 kb)