Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
See page 8 of this manual for more specific pressing tips. 7. Once pressing tasks are complete, immediately set On/Off Switch to “Off” (O) position and unplug grounded power cord from electrical outlet. Refer to page 9 of this manual for further information about cleaning and storage of Fabric Steam Press. 7 Top Innovations, Inc. USING THE FABRIC STEAM PRESS USING THE FABRIC STEAM PRESS STEAM BURST 1. Hold Pressing Plate approximately 75 mm. above Ironing Board. 2. Press Steam Burst Button to release a burst of steam onto fabric. 3. Lower Pressing Plate onto fabric, then raise once again. 4. Repeat steps 1-3 above until fabric is smooth and wrinkle-free. PRESSING AND STEAMING TIPS Pressing Shirts and Blouses 1. Place shoulder yoke on Ironing Board first and press. 2. Next, place sleeves onto Ironing Board with fold parallel to long seam and press. 3. Place cuffs onto end of Ironing Board and press. 4. Place bottom of shirt behind Ironing Board. Begin by pressing the side with pocket. Pull shirt towards you as you press each section. 5. Finish by pressing collar of shirt. Pressing Pants 1. Place Pressing Cushion under waistband and press, repositioning waistband until completely pressed. 2. To press inseam, place Pressing Cushion under area to be pressed. 3. Place pleated area on Ironing Board. Carefully fold pleats and press. 4. Embroidery should be placed face down on Ironing Board to reduce wear and prevent damage to delicate areas. Other Techniques • Placing Pressing Cushion between fabric and Pressing Plate may help with delicate fabrics. • Buttons and zippers: if you have older types of buttons or zippers, you may need to take special care to avoid melting. In order to do so, place garment face-down and cover with Pressing Cushion before pressing. • Spray Bottle may be used to spray fabrics lightly. This will further help to remove exceptionally stubborn wrinkles. • Place a damp cloth over fabric before pressing, which will help with stubborn wrinkles or heavy gauge fabrics. • To press large pieces of fabric, place entire piece behind Ironing Board. Pull fabric towards you, over Ironing Board, and lower Pressing Plate. Press fabric in sections until completed. Top Innovations, Inc. CARE &STORAGE GUIDELINES CARE &STORAGE GUIDELINES AUTO SHUT-OFF The Auto Shut-Off feature of the Fabric Steam Press includes both an Auto Shut-Off and an Auto Wake-Up. These multiple function safety features deactivate electrical power to the heater when the Pressing Plate has been left in closed position against the Ironing Board for more than 10 seconds. Heater deactivation is signaled by a beeping sound. Heater functionality is restored when the Pressing Plate is lifted back up. Power to the heater will also be cut if the Pressing Plate is left in the lifted position without use for approximately 15 minutes (signaled by a continuous beeping sound). The heating ability of the unit can be restored either by resetting the On/Off Switch, or by lowering and then raising the Pressing Plate. IMPORTANT: Auto Shut-Off does not mean that power to the unit is totally cut off. Power is always on, and the Power Indicator Light will remain illuminated until On/Off Switch is set to “Off” (O) position (FIGURE 1, page 7). CLEANING THE FABRIC STEAM PRESS 1. Fill Water Reservoir with water using procedure on page 7 of this manual. 2. Place Pressing Cushion in the middle of Ironing Board. 3. Place a clean towel over Pressing Cushion and Ironing Board. 4. Set Temperature Control Dial to the highest setting (LINEN). 5. When Steam Burst Ready Indicator Light illuminates, lower Pressing Plate onto Pressing Cushion. 6. Press Steam Burst Button six times. 7. Allow Pressing Plate to cool. 8. Clean Pressing Plate with damp cloth. Do not use abrasive materials, as this may damage Pressing Plate. 9. Ironing Board fabric cover is removable for cleaning. Hand wash only with mild detergent. PROPER STORAGE 1. Once pressing is complete, immediately turn unit off and unplug power cord from electrical outlet. 2. Allow unit to cool completely (at least 30 minutes). 3. Lower Pressing Plate down, and turn Locking Knob to “Lock” position. 4. Wrap up power cord and place in Cord Storage Compartment. 5. Store all accessories safely away, preferably near Fabric Steam Press. 6. Store Fabric Steam Press in a cool, dry place. 9 Top Innovations, Inc. TROUBLESHOOTING &CUSTOMER SUPPORT TROUBLESHOOTING &CUSTOMER SUPPORT PROBLEM POSSIBLE CAUSE SOLUTION Unit fails to heat up and steam. Power Indicator Light does not illuminate. Unit is not plugged in. Plug into electrical outlet. Household Circuit Breaker / Ground Fault Interrupter has tripped or blown a fuse. Reset Circuit Breaker / Ground Fault Interrupter, or replace fuse. If you need assistance, contact a licensed electrician. Unit fails to heat up and steam. Power Indicator Light does illuminate. Auto Shut-Off has engaged. Refer to Auto Shut-Off section on page 9 of this manual for proper procedure. Water Reservoir is ...
Dieses Handbuch ist für folgende Modelle:Bügeleisen - STEAM FAST SP-660 (225.02 kb)