• For best results in windy conditions, position narrow end of tent into the wind. • Enlist the help of at least one other person to assist you when it is time to assemble the tent. Pole Descriptions Pole Pole Pole Description Qty. Dia. Repair Kit Replacement Kit Main Pole, black 2 11mm 501000539 501000549 Main Pole, grey 1 11mm 501000539 501000549 Rainfly Pole, black, long 1 11mm 501000539 501000549 Awning Pole, black, short 1 6.9mm 501000542 501000552 To Set Up Tent 1. Unfold tent and spread o

Do not use in unventilated or enclosed areas to avoid endangering your life. 7. Keep lantern away from flammables. Never allow fabric, dothing, or any flammable material to come within 4 ft. (12m) of the top and 1ft. (.3 m) of the side of the lantern. 8. Use for lighting only. Never alter in any way or use with any device or part not expressly approved by Coleman. Do not use as a space heater. 9. Replace any mantle with a hole in it. A hole can cause lantern to overheat and create a hazard.

9180B3151_ Poles (1) Rainfly Part No. 9180B3251 Pole Rainfly Part No. 9180B3351 1 Layout & Positioning of Tent, Pole Assembly - Layout and position tent with door facing desired direction. (illus. 1) - Unzip door. - Stake down tent corners only, using the rings at the end of the stake loops. (illus.2) Keep the floor taut. - Assemble frame poles by interlocking shock-corded poles. This will make two long poles. - Insert the poles diagonally into pole sleeves. The center of the poles sho

Push down on steel button on tapered end and insert into end with four holes. NOTE: Make sure steel button locks into third hole on pole as shown. (Fig.4) 5. Insert curved end of Leg Poles (with red marking) into the ends of the Ridge Poles (with red marking). Insert curved end of remaining short Leg Poles into the ends of the remaining Ridge Poles. (Fig. 5 & 6) Button in third hole Fig. 4 Ridge Pole with Red Marking Fig. 5 Sleeve with Red Trim Curved End of Long Leg Pole Fig. 6 Curved Ridge Pol

9392-2281 Hub (1) Part No. 9392-2351 1 Pole Assembly -You will need to assemble and connect one pole at a time to the hub. -Do not completely assemble poles. a) Beginning at spring-clip end of pole, assemble all but the last shock-corded section. The pole and one section should curve downward. (illus. 2) b) Insert the spring-clip end into one of the hub ports until it clicks into position. (illus. 1), (illus. 2) c. Repeat for each of the five remaining poles (illus. 2) Illus. 2 Shelter

• Select a level campsite clear of rocks, branches, and other hard or sharp objects, to install your tent. WARNING: Keep clear of overhead power lines. • Do not set up your tent under trees. • For best results in windy conditions, position end of tent into the wind. • Enlist the help of at least one other person to assist you when it is time to assemble the tent. Parts and Components Description Part Number Main Pole, Black (1) 5010000372 Side Poles, Gray (2) 5010000370 Rainfly 5010000371 To Set

SOME STATES, PROVINCES, OR JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE. How to Obtain Warranty Service Take the product to an authorized Coleman service center. You can find the nearest authorized Col

(continued on other side) Extend the Tent Frame Raise the Tent ....Stand the tent upright with the hub assembly at the top. (Fig. 1) ....Unfold the arms of the tent downward until they lay flat on the ground. (Fig. 2) 1 2 3 Verify Connections between Tent and Frame Poles .... Verify the clips along the edges of the tent are properly attached to the frame poles. (Fig. 7 and Fig. 8) .... Unfold the arm joints located at each of the tent corners. The tent will raise as the leg poles are extended. (

• For best results in windy conditions, position narrow end of tent into the wind. • Enlist the help of at least one other person to assist you when it is time to assemble the tent. Pole Descriptions Pole Pole Pole Description Qty. Dia. Repair Kit Replacement Kit Main Body Pole, black 2 11mm 501000539 501000549 Side Body Pole, grey 2 9.5mm 501000540 501000548 Rainfly Pole, black 1 11mm 501000539 501000549 Vertical Door Pole, black, short w/rubber tips 1 6.3mm 501000543 501000545 Door Pole, black

5010000474 (1) Rear Pole (Blue Sticker) Part No. 5010000475 (2) Rear Brace Poles (Blue Sticker) Part No. 5010000476 (6) Center Upright Poles (Red Sticker) Part No. 5010000477 Rainfly Part No. 5010000481 1 Layout & Positioning of Tent - Layout and position tent with screen room facing desired direction. (illus. 1) - Stake down tent, starting with the corners. Do not stretch too tight. Angle the stakes slightly toward the tent. (illus. 2) Keep the floor taut. - Stake down the remainder o