Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Nikon
Dateigröße: 1.7 mb
Dateiname:
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
• The SCSI cable must not be extended beyond a total length of 19 feet (6 meters), or else failure may result. • If you use the type of terminator that is inserted between the SCSI cable and SCSI interface connector, install a terminator independent of the other SCSI connector of the LS-1000. • Terminators must be attached to the devices located at both ends of the SCSI chain. If the host computer is a Macintosh, the Macintosh itself will provide termination at one end of the chain. If the host computer is an IBM PC/AT or compatible, equipped with an SCSI board, the SCSI board itself will present termination at one end of the chain. Note that when an SCSI chain connection is made inside a computer, the end of the SCSI device inside the computer will become the end terminal. • Before installing an SCSI board, be sure to read the user’s manual provided with the board. The numbers for the I/O address, interrupt level (INT) and DMA channel might be used for other interface boards and peripheral devices. If so, change them as explained in the manual. - 24 4.4 4.4 The SCSI ID for the LS-1000 is set at “5” when the unit is shipped. If other SCSI devices are connected to your computer, make sure that the SCSI ID for the LS-1000 is different from those assigned to other SCSI devices. Note that in the case of a host computer which has a built-in SCSI hard disk or built-in CD-ROM, the ID numbers of the host CPU and each SCSI device have already been assigned. If the IDs are the same, you must change the ID number of the other SCSI device or the ID of the LS-1000 to avoid any conflict. Remarks • To change the ID, confirm that the LS-1000 power is off. The ID cannot be changed when the power is on. • As 7 has been assigned for the CPU and 0 has been assigned to the built-in hard disk for a Macintosh, and 0 and 7 have also been assigned to other personal computer systems, any number from 1 to 6 is recommended for the ID number. • If the same ID numbers are assigned, the system might not function, or important data on the hard disk might be destroyed. It is therefore essential to check the ID numbers carefully before connecting the LS-1000. - 25 5. 5. 5.1 Turning on the Power Turn the LS-1000 on first, the other SCSI devices next, and the host computer last. After turning the power on, the LED will begin to blink to indicate scanner initialization. POWER ON Remarks • To turn the LS-1000 power off, turn the host computer off first, the other SCSI devices next, and the LS-1000 last (reverse order from switching on). • Once the power is turned off, please wait five seconds or more before turning the power on again. • Do not turn the power on/off while the scanner is scanning. - 26 5.2 5.2 The LS-1000 can scan different types of 35mm positive/negative monochrome/color images. In addition, it can scan a film strip of up to 6 images or single mounted film. Insertion of Mounted slides The LS-1000 can scan mounted slides as they are. • Confirm that the thickness of the mounted slides to be scanned is between 1.1mm and 3.0mm. • Ensure that the emulsion surface is facing in the proper direction. When the LS-1000 is installed vertically, insert the mounted slide so that the emulsion surface is facing toward the right (shiny surface facing left). When the LS-1000 is installed horizontally, insert the mounted slide so that the emulsion surface is facing downward (shiny surface facing upward). * All film has an emulsion surface and a base surface. The emulsion surface is slightly convex and concave. The base surface is neither concave nor convex and is shinier than the emulsion surface. Insert the mounted slide lengthways until it touches the back inner wall. Note: Do not insert the mounted slide so that the width and length of the mount are reversed. If you do so, the LS-1000 will not be able to scan both sides of the mounted slide. - 27 The standard orientation of a mounted portrait or landscape The standard orientation of a mounted portrait or landscape slide is shown below. (If the top and bottom are reversed, modification is possible by using the software.) Orientation of a portrait slide - 28 Insertion of Strip film Insertion of Strip film Step 1 Remove the adaptor snap and open the upper holder. Be sure the word Nikon, printed on the adaptor cover of the upper holder is facing upward. Insertion Upper holder Adaptor cover Adaptor snap direction Step 2 Place the strip film on the concave section which is fixed in the adaptor of the lower holder. Be sure to place the strip film so that the emulsion surface will be facing down (the shiny surface will be facing up). The direction is correct if the image number can be read. Strip film Aperture Lower holder - 29 Step 3 Step 3 Align each image of the strip film with an aperture in the lower Close the upper holder, aligning both ends of the upper holder holder. and the lower holder. Fasten the snaps at both ends of the holder after securing the adaptor cover and fastening the adaptor's s...