or 1-800-265-6778 in Canada SAVE THIS MANUAL FOR FUTURE REFERENCE SPECIFICATIONS: Length of stroke 1 in. (25.4mm) Strokes per minute 0-2000 spm Length (without blade) 17 in. (430 mm) Engine Type Air Cooled 2 Cycle Gasoline Engine Displacement 15.9 cc Starting System Recoil Carburetor Diaphram Fuel Tank Capacity 0.35 literes Net weight 11 lbs. STOP TABLE OF CONTENTS TABLE OF CONTENTS ¦ Table of Contents ..............................................................................................

A damaged battery is subject to explosion. Properly dispose of a dropped or damaged battery immediately. n Batteries vent hydrogen gas and can explode in the presence of a source of ignition, such as a pilot light. To reduce the risk of serious personal injury, never use any cordless product in the presence of open flame. An exploded battery can propel debris and chemicals. If exposed, flush with water immediately. n Do not charge battery tool in a damp or wetlocation. Following this rule will r

n Green LED on = Fully charged and in maintenance charge mode. n Green LED on = When battery pack is inserted intocharger, indicates hot battery pack or that battery pack is out of or below normal temperature range. n Yellow and Green LEDs on = Deeply discharged ordefective battery pack. n No LED on = Defective charger or battery pack. CHARGING THE BATTERY PACK Battery packs for this tool have been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it un

A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless indicated elsewhere in this operator's manual. ¦ DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center. ¦ DRUGS, ALCOHOL, MEDICATION. Do not operate tool while under the influence of drugs, alcohol, or any medication. ¦ CUTTING INTO ELECTRICAL WIRING IN WALLS AND FLOORS CAN CAUSE THE BLADE AND METAL PARTS TO BECOME

WARNING: Do not allow familiarity with your circular saw to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. OPERATION OPERATION LED FUNCTION OF CHARGER 1400667 See Figure 2. LED WILL BE LIGHTED TO INDICATE STATUS OF CHARGER AND BATTERY PACK: ¦ Red LED Lighted = Fast Charging Mode. ¦ Green LED Lighted = Slow Charging Mode and Fully Charged Battery Pack. ¦ Yellow and Green LED Lighted = Soft Start Mode, or After 1/2 Hour Equals Hot or Defect

It runs through normal 120-V alternating current power. When on, the saw blade has a stroke of 19/16 inches moving at a maximum speed of 2800 strokes per minute. The entire assembly, including the removable blade, weights 6.3 pounds. The saw has 6 speed settings, a trigger which determines whether the saw is on or off, and interchangeable blades. After completing the model and assembling it, we will attempt to animate several aspects of the construction and functions of the saw. Finally, we will

VARIABLE SPEED See Figure 2. Your reciprocating saw has a variable speed control selector designed to allow operator control and adjustment of speed and power limits. The speed and power of your saw can be increased or decreased by rotating the variable speed control selector in the direction of the arrows shown in figure 2. NOTE: Hold your saw in normal operating position and turn the variable speed control selector clockwise to increase the speed and power of your saw. Turn counterclockwise to

PARTS LIST Key Part No. Number Description Quan. Key Part No. Number Description Quan. 1 990496-016 Cord .................................................................... 1 2 968775-001 Screw (M3 x 7 Fil. Hd.) ....................................... 2 3 617966-028 Screw (#8-10 x 1/2 in. Pan Hd.) ......................... 1 4 617966-030 Screw (#8-10 x 5/8 in. Pan Hd.) ....................... 10 5 973703-001 Logo Plate .......................................................... 1 6 617966-032 Sc

Replacement blades for this saw are available from your nearest Ryobi dealer. Page 6 OPERATION OPERATION TO INSTALL BLADES See Figure 3. ¦ UNPLUG YOUR SAW. WARNING: Failure to unplug your saw could result in accidental starting causing serious injury. ¦ Remove the 5/32 in. allen wrench provided with this saw from allen wrench holder. NOTE: Allen wrench holder is located in bottom portion of saw handle. See Figure 1. ¦ Loosen the blade clamp screw enough to permit the saw blade to be inserted bet

Make sure saw blade is clear of any foreign material and that power cord and extension cord are out of the blade path. Be sure material to be cut is held firmly. Small work pieces should be securely clamped in a vise or with clamps to the work bench or table. Mark the line of cut clearly. Depress the trigger switch starting the cutting action, set the base assembly against the work, then move the blade into the work. DO NOT FORCE. Use only enough pressure to keep the saw cutting. Let the blade a