Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
!9 KEYBOARD connector • To use a keyboard, connect it to this connector. • The connector is a mini DIN type 6-pin connector. @0 ANALOG IN connectors • These are active balanced inputs using XLR type connectors. • Connect these connectors to the balanced analog output connectors on an amplifier or console. • Pin layout: 1. Common 2. Hot 3. Cold • Applicable connector: Cannon XLR-3-32 or equivalent. @1 ANALOG OUT connectors • These are active balanced outputs using XLR type connectors. • Connect these connectors to the balanced analog input connectors on an amplifier or console. • Pin layout: 1. Common 2. Hot 3. Cold • Applicable connector: Cannon XLR-3-31 or equivalent. NOTE: Do not short-circuit the hot or cold pin with the common pin. @2 IN LEVEL L/R controls • Use these controls to adjust the level of the audio signals from the ANALOG IN connectors. @3 OUT LEVEL L/R controls • Use these controls to adjust the level of the audio signals from the ANALOG OUT connectors. @4 DIGITAL OUT (AES/EBU) connector • This is an active balanced output using an XLR type connector. • Connect this connector to the balanced digital input connector on an amplifier or console. • Signal format: AES/EBU or SPDIF. • Pin layout: 1. Common 2. Cold 3. Hot • Applicable connector: Cannon XLR-3-31 or equivalent. • This unit uses a balanced digital output. A conversion circuit is necessary for connection to an unbalanced circuit. Example of balanced/unbalanced conversion circuit. 74HCU04 ( 4 / 6 ) +5V +5VGND+ 1 3 9 1113 100 . 16V +5V +5V IN TO (3) DN-991R (2) 75.33. 16V+ + 33 4 86 5 4 7 14 74HCU04 ( 1 / 6 ) SN75157 ( 1 / 2 ) 110. 1SS270 100 . 16V H C GND 100P 5 : 1 OUT DIGITAL (1) OUT @5 MONITOR jack • Connect headphones with an impedance of 30 to 40 ./ohms. @6 DIGITAL IN (AES/EBU) connector • This is an active balanced input using an XLR type connector. • Connect this connector to the balanced digital output connector on an amplifier or console. • Signal format: AES/EBU or IEC958 Type I • Pin layout: 1. Common 2. Cold 3. Hot • Applicable connector: Cannon XLR-3-32 or equivalent. • This unit uses a balanced digital input. A conversion circuit is necessary for connection to an unbalanced circuit. Example of unbalanced/balanced conversion circuit. TO DN-991R DIGITAL IN WARNING: Turn PITCH control OFF when making digital recording. Most digital recorders will not accept a variable pitched digital signal. @7 POWER switch • This turns the set on and off. @8 AC inlet • Connect the included power cord here. 9 ENGLISH @9 REMOTE connector • This is a parallel remote connector. Use it to control the DN-M991R with dry contact circuit connections. • Applicable connector: 25-pin D-sub (male) • Connector signal layout: Pin No. Hot Start ON Hot Start OFF Level Signal name I/O Signal name I/O 1 FG – FG – 14 PLAY CODE 1 tally O PLAY tally O TTL (lol=20 mA) 2 PLAY CODE 1 command I PLAY command I HCMOS (li–3 mA) 15 PLAY CODE 2 tally O PAUSE tally O TTL (lol=20 mA) 3 PLAY CODE 2 command I PAUSE command I HCMOS (li–3 mA) 16 PLAY CODE 3 tally O STDBY/CUE tally O TTL (lol=20 mA) 4 PLAY CODE 3 command I STDBY/CUE command I HCMOS (li–3 mA) 17 PLAY CODE 4 tally O END CUE tally O TTL (lol=20 mA) 5 PLAY CODE 4 command I TRACK (+) command I HCMOS (li–3 mA) 18 Tally common O Tally common – 6 PLAY CODE 5 command I TRACK (–) command I HCMOS (li–3 mA) 19 REPEAT command I REC command I HCMOS (li–3 mA) 7 STOP command I SEARCH (FWD) command I HCMOS (li–3 mA) 20 REPEAT tally O CUE tally O TTL (lol=20 mA) 8 LOAD command I SEARCH (REV) command I HCMOS (li–3 mA) 21 LOAD tally O REC tally O TTL (lol=20 mA) 9 FADER START command – FADER START command I PHOTO COUPLER 22 Tally power supply O Tally power supply – +5 V, 20 mA 10 FADER START return & – Command common – (li=10 mA) 23 Command common – Command common – 11 Reserved – REC E.O.M. – 24 Reserved – E.O.M. tally O DRY CONTACT 12 Reserved – Reserved – 25 Reserved – E.O.M. tally O DRY CONTACT 13 Hot Start ON (Low) – Hot Start OFF (High) I HCMOS (li–3 mA) NOTES: • The tally output pin has open collector IC specifications (Imax. 20 mA, Vmax. 5 V), but the maximum supply current is 80 mA, so use with a total load current of 80 mA or less. • 13 Pin enable when Hot start (Preset 36)) set up off mode. (3) Display Window #0 TRACK NO. indicator • This lights When the track number display shows the selected track number. #1 PROGRAM indicator • This lights when the Program play mode is set. #2 DISC NAME/TRACK NAME/DATE indicators • “DISC NAME” lights when the disc name is displayed on the character display, “TRACK NAME” lights when the track name is displayed, and “DATE” lights when the date is displayed. #3 Level display • This displays the playback level during playback, the input level during recording. #4 EDIT indicator • This lights when the edit mode is set. #5 TOC indicator • This lights when it is necessary to rewrite the TOC (UTOC) due to editing, etc • This flashes while the TOC (UTOC) is being written. #6 DIGITAL IN indicator...